Mastering Basic Plumbing When You Install a Bathtub
Mastering Basic Plumbing When You Install a Bathtub
Blog Article
Listed here below you can get some first-rate data concerning How to Install a Bathtub Yourself.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Mounting a tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, and often, tiling abilities. Replacing an old bath tub with a new one is additionally a reasonably difficult task. If the old bathtub is easily obtainable, the task can relocate immediately; if you have to open up a wall to eliminate the old tub and place the new bathtub, the task is a lot harder. In either situation, the task is within a residence handyman's abilities, although you will certainly require an assistant to leave the old bathtub and also set in the brand-new one. Make certain you have qualified yourself for the task as well as are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed project, it is much better to consider utilizing one before you begin. Opportunities are you might need an expert plumber to make tube links.
This post will help you set up a brand-new bath tub in your shower room if you have actually already gotten a brand-new bathtub and also don't need to alter the arrangement of your previous water system pipelines.
Your tools and also product list ought to comprise the following:
Getting ready for the Installment
To start with, the sustaining framework supplied with the bathroom needs to be fitted (if called for) according to the supplier's directions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to ensure that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets system to stop stress on the bathtub.
Fit the flexible faucet connectors to the bottom of both faucets using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you utilize every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its last position.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, then the first thing you must do is disconnect the water supply. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing taps can be quite problematic because of the restricted gain access to that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipelines. When the supply pipes have been removed, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this process. Once the faucets have been removed, the holes in the bath/basin will need to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the new taps, compare the pipeline connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Tub
Making use of the two wood boards under its feet, put the bathtub in the needed setting. The wooden boards are valuable in evenly spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 little points.
The next goal is to make sure that the bathtub is leveled all round. This can be attained by checking the level and readjusting the feet on the bath tub till the level reads level.
To mount taps, fit all-time low of the furthest adaptable tap connector to the ideal supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Turn on the water and also examine all joints as well as brand-new pipework for leaks and tighten them if required. Fill up the bathtub as well as also inspect the overflow outlet and the regular electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the supplier's instruction manual. Tiling and securing around the bath tub ought to wait up until the bathtub has actually been utilized a minimum of once as this will settle it into its last placement.
Fitting New Touches
If the tails of the new taps are plastic, after that you will need a plastic port to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end offers a link to the existent supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin making sure that the washers remain in location between the tap and also the sink. Safeguard the tap in place with the maker provided backnut. As soon as the faucet is safely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous kind needs to be attached to the faucet finishes initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to break a rigid seal, triggering the water to permeate the wall surface in between the bathroom and the tiling, resulting in difficulties with dampness and possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your components and also fittings. They are sold in tubes and also cartridges, and are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of drenched newspaper or soft rope. Remember to always load the tub with water prior to sealing, to permit the movement experienced when the tub is in usage. The sealant can break fairly very early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise easily offered on the marketplace. It is suggested to fit the tiles utilizing waterproof or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
I came across that content on Installing A Bathtub while doing a search on the web. Liked our posting? Please share it. Let another person locate it. Thank you for taking the time to read it.
Schedule Now Report this page